manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

6

EAU00794

Checking the steering 

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place a stand under the engine to

raise the front wheel off the
ground.

EW000115

WARNING

@ 

Securely support the motorcycle so
that there is no danger of it falling
over. 

@

2. Hold the lower ends of the front

fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steer-
ing.

EAU01144

Checking the wheel bearings 

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer
check the wheel bearings.

u5gk12.book  Page 35  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands