manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 60

PERIODIC MAINTENANCE AND MINOR REPAIR

6-9

6

EAU03340

Panel A

To remove the panel

1. Remove cowling A. (See page 6-8

for cowling removal and installa-
tion procedures.)

2. Remove the screws, and then take

the panel off.

To install the panel

1. Place the panel in the original po-

sition, and then install the screws.

2. Install the cowling.

EAU01315

Panel B

To remove the panel
Remove the screws, and then take the
panel off.
To install the panel
Place the panel in the original position,
and then install the screws. 

EAU03329

Checking the spark plugs 

The spark plugs are important engine
components, which are easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plugs should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
the condition of the spark plugs can re-
veal the condition of the engine.

To remove a spark plug

1. Remove the spark plug cap.

1. Screw (

×

 2)

1. Screw (

×

 2)

1. Spark plug cap

u5gk12.book  Page 9  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands