manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 24

INSTRUMENT AND CONTROL FUNCTIONS

3-3

3

EAU00101

Tachometer 

The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.

EC000003

CAUTION:

@ 

Do not operate the engine in the
tachometer red zone.
Red zone: 8,500 r/min and above 

@

EAU01652

Coolant temperature gauge 

With the key in the “ON” position, the
coolant temperature gauge indicates
the temperature of the coolant. The
coolant temperature varies with chang-
es in the weather and engine load. If
the needle reaches or enters the red
zone, stop the motorcycle and let the
engine cool. (See page 6-49 for further
instructions.)

EC000002

CAUTION:

@ 

Do not operate the engine if it is
overheated. 

@

EAU00118

Handlebar switches 

EAU00122

Dimmer switch “LIGHTS” 

Set the switch to “HI” for the high beam
and to “LO” for the low beam.

EAU01189

Turn signal switch “TURN” 

To signal a right-hand turn, push this
switch to the right. To signal a left-hand
turn, push the switch to the left. When
released, the switch returns to the cen-
ter position.

1. Tachometer
2. Tachometer red zone

1. Coolant temperature gauge
2. Coolant temperature gauge red zone

1. Dimmer switch “LIGHTS”
2. Turn signal switch “TURN”
3. Horn switch “HORN”

u5gk12.book  Page 3  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands