manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 116

CONSUMER INFORMATION

9-4

9

EAU01053

Motorcycle noise regulation 

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:

Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-
hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.

These acts include tampering with the following systems; i.e., modification, removal, etc.

CL-01E

Exhaust system

Muffler
Exhaust pipe
Silencer

Intake system

Air cleaner case
Air cleaner element
Intake duct

u5gk12.book  Page 4  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands