Yamaha Star XV19CTSZ 2009 Owner'S Manual Download

Page: 39 / 104

INSTRUMENT AND CONTROL FUNCTIONS

4-23

EAU44892

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

U2C514E0.book Page 23 Tuesday, September 8, 2009 10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands

Yamaha Star XV19CTSZ 2009, Owner'S Manual

Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands