Yamaha Star XV19CTSZ 2009 Owner'S Manual Download | Manualshive

Page: 71 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-23

7

EAU23202

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10731

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the sidestand could contact the
ground and distract the operator, re-
sulting in a possible loss of control.

EAU23251

Lubricating the rear suspen-
sion

The pivoting points of the rear suspen-
sion must be lubricated by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.

Recommended lubricant:

Silicone grease

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U2C514E0.book Page 23 Tuesday, September 8, 2009 10:12 AM

«
...
69
70
71
72
73
...
»

Summary of Contents for Star XV19CTSZ 2009









































































































Reviews:

No comments

Related manuals for Star XV19CTSZ 2009

Brand: Palm Pages: 14

Brand: Fantic Motor Pages: 130

Brand: Keis Pages: 2

Brand: Sachs Bikes Pages: 83

Brand: AJP Pages: 191

Brand: SRC Pages: 5

Brand: KTM Pages: 163

Brand: Braaap Pages: 40

Brand: KTM Power Parts Pages: 7

Brand: Honda Pages: 60

Brand: GAS GAS Pages: 107

Brand: DYNATEK Pages: 6

GHJ 10,8+18V Unisex

Brand: Bosch Pages: 14

Brand: Bosch Pages: 28

Brand: Bosch Pages: 145

Brand: hepco & becker Pages: 2

Brand: Kemppi Pages: 10

Brand: hepco & becker Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands