manualshive.com logo in svg

Yamaha Star XV19CTSZ 2009, Owner'S Manual

Share
Download
Yamaha Star XV19CTSZ 2009 Owner'S Manual Download Page 35

INSTRUMENT AND CONTROL FUNCTIONS

4-19

4

To close a sidebag lid

1. Fold the sidebag lid down so that

the latch snaps into place.

2. Turn the key clockwise, and then

remove it.

To remove a sidebag

1. Open the sidebag lid.
2. Turn the fasteners counterclock-

wise, and then remove the side-
bag by pulling it upward.

TIP

The fasteners will come loose after the
sidebags are removed. Be sure not to
lose the fasteners.

To install a sidebag

1. Open the sidebag lid.
2. Place the sidebag on the bracket,

and then align all holes in the side-
bag with the holes in the holders
on the bracket.

3. Insert the fasteners through the

holes in the sidebag into their hold-
ers, and then turn them clockwise
until they stop.

1. Fastener

1. Fastener

1

1. Hole
2. Holder

1. Fastener

U2C514E0.book  Page 19  Tuesday, September 8, 2009  10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands