Yamaha Star XV19CTSZ 2009 Page 33 Owner'S Manual Download

Page: 33 / 104

INSTRUMENT AND CONTROL FUNCTIONS

4-17

EAU39141

Windshield

To remove the windshield

1. Insert the key into the windshield

lock, turn it clockwise and then re-
move the key.

2. Remove the windshield by push-

ing it forward, and then pulling it
upward as shown.

WARNING! Be

careful not to push the motorcy-
cle forward when removing the
windshield. The motorcycle
could fall off the sidestand.

[EWA14321]

NOTICE

ECA15350

Securely hold the windshield to pre-
vent it from falling when removing.

To install the windshield

1. Fit the slot in each windshield

bracket (left and right side) into its
holder.

WARNING! Make sure

that the throttle cables are not
pinched.

[EWA14301]

2. Push the windshield backward un-

til it snaps into place.

3. Insert the key into the windshield

lock, turn it counterclockwise until
it stops to lock the fastener, and

1. Key

2. Unlock.

1. Slot
2. Holder

3. Throttle cable

U2C514E0.book Page 17 Tuesday, September 8, 2009 10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands

Yamaha Star XV19CTSZ 2009, Owner'S Manual

Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands