manualshive.com logo in svg

Yamaha Star XV19CTSZ 2009, Owner'S Manual

Share
Download
Yamaha Star XV19CTSZ 2009 Owner'S Manual Download Page 78

PERIODIC MAINTENANCE AND ADJUSTMENT

7-30

7

EAU24181

Tail/brake light 

This model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

EAU38382

Replacing a turn signal light 
bulb 

1. Remove the turn signal light lens

by removing the screw, and then
turning the lens counterclockwise.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by turning it clock-

wise, and then installing the screw.

NOTICE:

 Do not overtighten the

screw, otherwise the lens may
break.

 [ECA11191]

EAU24330

License plate light 

If the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.

1. Screw

U2C514E0.book  Page 30  Tuesday, September 8, 2009  10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands