Yamaha Star XV19CTSZ 2009 Owner'S Manual Download

Page: 76 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-28

oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

●

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

Removing the headlight unit

1. Remove the windshield. (See

page 4-17.)

2. Remove the headlight body cover

by removing the bolts.

3. Disconnect the coupler shown.

4. Remove the headlight unit by re-

moving the screws.

To replace the high beam headlight
bulb

1. Remove the headlight bulb holder

cover by turning it counterclock-
wise.

1. Do not touch the glass part of the bulb.

1. Bolt

2. Headlight body cover

1. Coupler

1. Screw

U2C514E0.book Page 28 Tuesday, September 8, 2009 10:12 AM

Summary of Contents for Star XV19CTSZ 2009









































































































Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands

Yamaha Star XV19CTSZ 2009, Owner'S Manual

Search results

Summary of Contents for Star XV19CTSZ 2009

Reviews:

Related manuals for Star XV19CTSZ 2009

Brands by name

Popular brands