Yamaha R-N803 D Owner'S Manual Download Page 64

Page: 64 / 73

Troubleshooting

■

Bluetooth

The DAB radio
reception strength is
poor, and noise
(such as hiss,
crackle and jitter)
can be heard.

The DAB radio signal is weak.

Change the antenna height, direction, or place of
installation.

The DAB information
cannot be displayed
or is inaccurate.

The DAB station may be temporarily out
of service, or the DAB station
information is not provided by the DAB
broadcaster.

Contact the DAB broadcaster.

―

Problem

Possible cause

Remedy

page

The unit cannot
connect to a

Bluetooth

device.

The

Bluetooth

function is disabled.

In the “Setup” menu, set “

Bluetooth

(On/Off)” to

“On”.

The unit is connected to a different

Bluetooth

device.

Disconnect the current

Bluetooth

connection and

connect with the desired

Bluetooth

device.

The unit is too far from the

Bluetooth

device.

Move the

Bluetooth

device closer to this unit.

―

A device emitting electromagnetic waves
(such as a microwave oven and a
wireless device) may be located nearby.

Do not use this unit near devices that emit
electromagnetic waves.

―

The

Bluetooth

device does not support

the A2DP protocol.

Use a

Bluetooth

device that supports the A2DP

protocol.

The connection profile registered in the

Bluetooth

device may not be functioning

correctly for some reason.

Delete the connection profile in the

Bluetooth

device, and then connect the

Bluetooth

device to this

unit.

The passkey on the

Bluetooth

adapter or

other device may be set to a code besides
“0000”.

Use a

Bluetooth

device on which the passkey is set

to “0000”.

―

No sound can be
heard, or the sound
cuts off
intermittently.

The volume on the

Bluetooth

device is

too low.

Raise the volume on the

Bluetooth

device.

―

The sound output on the

Bluetooth

device may not be set to this unit.

Select this unit as the output destination on the

Bluetooth

device.

The connection to the

Bluetooth

device is

cut off.

Reconnect with the

Bluetooth

device.

The unit is too far from the

Bluetooth

device.

Move the

Bluetooth

device closer to this unit.

―

A device emitting electromagnetic waves
(such as a microwave oven and a
wireless device) may be located nearby.

Do not use this unit near devices that emit
electromagnetic waves.

―

Problem

Possible cause

Remedy

page

Summary of Contents for R-N803 D










































































Search results

Summary of Contents for R-N803 D

Reviews:

Related manuals for R-N803 D

Brands by name

Popular brands

Yamaha R-N803 D, Owner'S Manual

Search results

Summary of Contents for R-N803 D

Reviews:

Related manuals for R-N803 D

Brands by name

Popular brands