manualshive.com logo in svg

Yamaha MAJESTY YP250, Owner'S Manual

Share
Download
Yamaha MAJESTY YP250 Owner'S Manual Download Page 98

7-1

EAU03434

SCOOTER CARE AND STORAGE

7

Care

Care

While the open design of a scooter
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go
unnoticed on a car, however, it
detracts from the overall appearance
of a scooter. Frequent and proper
care does not only comply with the
terms of the warranty, but it will also
keep your scooter looking good,
extend its life and optimize its perfor-
mance.

Before cleaning

1. Cover the muffler outlet with a

plastic bag after the engine has
cooled down.

2. Make sure that all caps and cov-

ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly
installed.

3. Remove extremely stubborn dirt,

like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.

Cleaning

ECA00011

c

C

8

8

Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-
remove dirt, do not leave the
cleaner on the affected area
any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.

8

8

Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent
and water to clean plastic.

5SJ-28199-E2  8/9/02 4:06 PM  Page 96

Summary of Contents for MAJESTY YP250





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands