manualshive.com logo in svg

Yamaha MAJESTY YP250, Owner'S Manual

Share
Download
Yamaha MAJESTY YP250 Owner'S Manual Download Page 39

3-22

INSTRUMENT AND CONTROL FUNCTIONS

3

The sidestand switch may be defective.

The scooter should not be ridden

 until 

checked by a Yamaha dealer.

YES

NO

With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to “

#

”.

3. Turn the key to “ON”. 
4. Keep the front or rear brake applied.
5. Push the start switch.

Does the engine start?

The brake switch may be defective.

The scooter should not be ridden

 until 

checked by a Yamaha dealer.

With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.

Does the engine start?

With the engine still running:
9. Move the sidestand down.

Does the engine stall?

The sidestand switch may be defective.

The scooter should not be ridden

 until 

checked by a Yamaha dealer.

NOTE:

This check is most reliable if performed with
a warmed-up engine.

YES

NO

The system is OK. 

The scooter can be ridden.

YES

NO

5SJ-28199-E2  8/9/02 4:05 PM  Page 37

Summary of Contents for MAJESTY YP250





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands