Yamaha MAJESTY YP250 Owner'S Manual Download Page 79 | Manualshive

Page: 79 / 116

background image

6-28

PERIODIC MAINTENANCE AND MINOR REPAIR

6

EAU00721

Checking the front and rear
brake pads

Front and rear brake pads, checking

The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart.

2. Install the brake caliper bolt, and

then tighten it to the specified
torque.

1

1.

Wear indicator groove

EAU04583

Front brake pads

Each front brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear
without having to disassemble the
brake. Check the brake pad wear as
follows.

1. Remove the brake caliper bolt,

and then tilt the caliper forward
to inspect the wear indicator
groove. If a brake pad has worn
to the point that the wear indica-
tor groove has almost disap-
peared, have a Yamaha dealer
replace the brake pads as a set.

1

2

1.

Brake caliper bolt

2.

Brake caliper

Tightening torque:

Brake caliper bolt:

26.5 Nm (2.65 m·kgf)

FRONT

5SJ-28199-E2 8/9/02 4:06 PM Page 77

«
...
77
78
79
80
81
...
»

Summary of Contents for MAJESTY YP250





















































































































Reviews:

No comments

Related manuals for MAJESTY YP250

Brand: Jetson Pages: 20

Brand: JDbug Pages: 63

Brand: Triumph Pages: 18

Brand: Kayoba Pages: 44

Brand: X-TREME Pages: 39

Brand: Nipponia Pages: 44

Brand: Denver Pages: 29

Brand: JBM Pages: 36

Brand: Acer Pages: 338

Brand: Myria Pages: 24

Brand: URB-E Pages: 20

Brand: URB-E Pages: 25

Brand: Jetson Pages: 8

Brand: e-mo Pages: 2

Brand: V&D Electric Bikes Pages: 18

Brand: besrey Pages: 10

Brand: E-Wheels Pages: 70

Brand: INOKIM Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands