Yamaha MAJESTY YP250 Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 116

background image

5-2

OPERATION AND IMPORTANT RIDING POINTS

5

NOTE:

If the engine does not start, release
the start switch, wait a few seconds,
and then try again. Each starting
attempt should be as short as possi-
ble to preserve the battery. Do not
crank the engine more than 10 sec-
onds on any one attempt. If the
engine does not start, try with the
throttle open 1/8 turn.

ECA00045

c

C

For maximum engine life, never
accelerate hard when the engine is
cold!

EAU00433

Starting off

Starting off

NOTE:

Before starting off, allow the engine
to warm up.

1. While pulling the rear brake lever

with your left hand and holding
the grab bar with your right hand,
push the scooter off the center-
stand.

2. Sit astride the seat, and then

adjust the rear view mirrors.

3. Switch the turn signal on.

4. Check for oncoming traffic, and

then slowly turn the throttle grip
(on the right) in order to take off.

5. Switch the turn signal off.

1

1.

Grab bar

5SJ-28199-E2 8/9/02 4:05 PM Page 45

«
...
45
46
47
48
49
...
»

Summary of Contents for MAJESTY YP250





















































































































Reviews:

No comments

Related manuals for MAJESTY YP250

Brand: Olsson and Brothers Pages: 25

Brand: Handicare Pages: 44

Brand: VMAX Pages: 24

Brand: X-TREME scooter Pages: 31

Brand: Hudora Pages: 12

Brand: SUPER 73 Pages: 21

Brand: Trikke Pages: 38

Brand: Malaguti Pages: 50

Brand: EZee Life Pages: 25

Brand: e-mo Pages: 2

Brand: TN’G Pages: 70

Brand: kikkaride Pages: 23

Brand: Pride Mobility Pages: 48

Brand: Yvolve Sports Pages: 30

Brand: Hudora Pages: 12

Brand: CPI Pages: 43

Brand: Razor Pages: 5

Brand: Woosh Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands