Yamaha MAJESTY YP250 Owner'S Manual Download Page 94

Page: 94 / 116

6-43

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU01581

Troubleshooting charts

Troubleshooting charts

Starting problems or poor engine performance

EW000125

Keep away open flames and do not smoke while checking or working on the fuel system.

Check the fuel level in
the fuel tank.

1. Fuel

There is enough fuel.

There is no fuel.

Check the compression.

Supply fuel.

The engine does not start.
Check the compression.

Operate the electric starter.

2. Compression

There is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealer
check the vehicle.

Remove the spark plug
and check the electrodes.

3. Ignition

Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.

Have a Yamaha dealer check the vehicle.

The engine does not start.
Have a Yamaha dealer
check the vehicle.

The engine does not start.
Check the battery.

Operate the electric starter.

4. Battery

The engine turns over
quickly.

The engine turns over
slowly.

The battery is good.

Check the battery lead connections,
and charge the battery if necessary.

Dry

Wet

Open the throttle halfway and operate
the electric starter.

5SJ-28199-E2 8/9/02 4:06 PM Page 92

Summary of Contents for MAJESTY YP250





















































































































Search results

Summary of Contents for MAJESTY YP250

Reviews:

Related manuals for MAJESTY YP250

Brands by name

Popular brands

Yamaha MAJESTY YP250, Owner'S Manual

Search results

Summary of Contents for MAJESTY YP250

Reviews:

Related manuals for MAJESTY YP250

Brands by name

Popular brands