manualshive.com logo in svg

Yamaha MAJESTY YP250, Owner'S Manual

Share
Download
Yamaha MAJESTY YP250 Owner'S Manual Download Page 112

INDEX

E

Engine break-in  ......................................5-4
Engine oil ..............................................6-14

F

Final transmission oil  ............................6-18
Front and rear brake lever free play, 

adjusting ............................................6-27

Front and rear brake pads, checking ....6-28
Front fork, checking  ..............................6-32
Fuel ......................................................3-14
Fuel consumption, tips for reducing  .......5-4
Fuel gauge  .............................................3-4
Fuel tank cap  ........................................3-13
Fuses, replacing  ...................................6-36

H

Handlebar switches  ..............................3-10

Dimmer switch  ...................................3-10
Engine stop switch  .............................3-12
Horn switch  ........................................3-10
Pass switch  ........................................3-10
Start switch  ........................................3-12
Turn signal switch  ..............................3-10

Headlight bulb, replacing  ......................6-37
Headlight variations  ..............................3-11

I

Identification numbers  ............................9-1
Ignition circuit cut-off system  ................3-21
Indicator lights  ........................................3-2

High beam indicator light  .....................3-2
Oil change indicator light  .....................3-2
Turn signal indicator lights  ...................3-2

K

Key identification number  .......................9-1

L

License plate light bulb, replacing  ........6-41

M

Main switch/steering lock  .......................3-1
Model label  .............................................9-2

P

Parking ...................................................5-5
Part locations ..........................................2-1
Periodic maintenance and lubrication 

chart .....................................................6-3

Pre-operation check list  ..........................4-1

R

Rider seat  .............................................3-16
Rider seat, adjusting .............................3-17

A

Acceleration and deceleration  ................5-3
Air filter and V-belt case air filter 

elements, cleaning  .............................6-21

Air flow louver  .......................................6-23
Anti-theft alarm (optional)  .......................3-9

B

Battery ..................................................6-34
Battery cover removal  ..........................6-34
Brake fluid level, checking  ....................6-29
Brake fluid, changing  ............................6-30
Brake lever, front  ..................................3-12
Brake lever, rear  ...................................3-13
Brake levers, lubricating  .......................6-31
Braking ...................................................5-3

C

Cables, checking and lubricating ..........6-30
Care ........................................................7-1
Catalytic converter ................................3-15
Centerstand and sidestand, checking 

and lubricating  ...................................6-31

Conversion table  ....................................8-5
Coolant .................................................6-19
Coolant temperature gauge ....................3-5
Cowlings and panel, removing and 

installing ...............................................6-6

D

Display, multi-function  ............................3-5

5SJ-28199-E2  8/9/02 4:06 PM  Page 110

Summary of Contents for MAJESTY YP250





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands