Yamaha GP800R WaveRunner 2003 Service Manual Download Page 81

Page: 81 / 247

4-30

FUEL

OIL PUMP

SERVICE POINTS

Oil pump inspection

1. Inspect:

●

Oil pump
Contaminants

→

Clean.

Damage/wear

→

Replace.

●

Oil pump joint piece
Damage/wear

→

Replace.

Oil hose inspection

1. Inspect:

●

Oil hose
Cracks/damage

→

Replace.

CAUTION:

If the oil feed hoses are not full of oil, fill
them up.

Check valve inspection

1. Check:

●

Check valve
Faulty

→

Replace.

Oil pump cable adjustment

1. Check:

●

Oil pump lever position
Incorrect

→

Adjust.

Checking steps:

●

Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.

●

Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.

Checking steps:

●

Fully close the carburetor throttle
valves.

●

Check that the mark

on the oil pump

lever is aligned with the mark

on the

oil pump body.

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands

Yamaha GP800R WaveRunner 2003, Service Manual

Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands