Yamaha GP800R WaveRunner 2003 Service Manual Download Page 75

Page: 75 / 247

4-24

FUEL

Regulator body inspection

1. Inspect:

●

Regulator body
Contaminants

→

Clean.

Damage

→

Replace.

●

Valve (clear film)

Damage

→

Replace.

Needle valve inspection

1. Inspect:

●

Needle valve

●

Needle valve seat
Contaminants

→

Clean.

Wear

→

Replace.

NOTE:

Always replace the needle valve and needle
valve seat as a set.

Jet and carburetor body inspection

1. Inspect:

●

Main jet

●

Pilot jet

●

Carburetor body
Clog/contaminants

→

Clean.

Damage/wear

→

Replace.

CAUTION:

Do not use a steel wire to clean the jets.
This may enlarge the jet diameters and
seriously affect performance.

Carburetor assembly

NOTE:

Before assembling the carburetor, make
sure to turn out the pilot screw the same
number of times, as noted before disassem-
bly, from the seated position to the set posi-
tion.

1. Adjust:

●

Trolling speed
Refer to “FUEL SYSTEM” in chapter 3.

CARBURETOR

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands

Yamaha GP800R WaveRunner 2003, Service Manual

Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands