manualshive.com logo in svg

Yamaha GP800R WaveRunner 2003, Service Manual

The Yamaha GP800R WaveRunner 2003 is a high-performance personal watercraft that offers thrilling rides on the open water. To ensure you have a safe and enjoyable experience, it is essential to refer to the comprehensive Owner's/Operator's Manual. You can easily download this manual for free from manualshive.com, empowering you with vital information to maximize your WaveRunner's performance.

Share
Download
background image

E

1 
2 
3 
4 
5 
6 
7 
8 
9 

POWR

CYLINDERS

................................................................................................... 5-20

EXPLODED DIAGRAM ........................................................................... 5-20
REMOVAL AND INSTALLATION CHART ............................................. 5-20
SERVICE POINTS ................................................................................... 5-21

Cylinder inspection ......................................................................... 5-21

PISTONS

....................................................................................................... 5-22

EXPLODED DIAGRAM ........................................................................... 5-22
REMOVAL AND INSTALLATION CHART ............................................. 5-22
SERVICE POINTS ................................................................................... 5-24

Piston pin clip removal and installation........................................ 5-24
Piston inspection............................................................................. 5-24
Cylinder and piston combination .................................................. 5-25
Piston ring inspection ..................................................................... 5-25
Piston pin and bearing inspection ................................................. 5-26

STARTER MOTOR

........................................................................................ 5-28

EXPLODED DIAGRAM ........................................................................... 5-28
REMOVAL AND INSTALLATION CHART  ............................................ 5-28

FLYWHEEL MAGNETO

................................................................................ 5-29

EXPLODED DIAGRAM ........................................................................... 5-29
REMOVAL AND INSTALLATION CHART ............................................. 5-29
SERVICE POINTS ................................................................................... 5-34

Drive coupling removal and installation ....................................... 5-34
Flywheel magneto removal and installation ................................ 5-34
Drive coupling inspection............................................................... 5-35
Flywheel magneto inspection ........................................................ 5-35
Starter clutch assembly inspection ............................................... 5-35

CRANKCASE

................................................................................................. 5-36

EXPLODED DIAGRAM ........................................................................... 5-36
REMOVAL AND INSTALLATION CHART ............................................. 5-36
SERVICE POINTS ................................................................................... 5-38

Crankcase inspection ...................................................................... 5-38
Crankcase installation..................................................................... 5-38

CRANKSHAFT

............................................................................................... 5-39

EXPLODED DIAGRAM ........................................................................... 5-39
REMOVAL AND INSTALLATION CHART ............................................. 5-39
SERVICE POINTS ................................................................................... 5-40

Crankshaft inspection ..................................................................... 5-40

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Reviews:

No comments

Related manuals for GP800R WaveRunner 2003

Jeanneau 64 Owner'S Manual preview
64
Brand: Jeanneau Pages: 80
KL Outdoor Sun Dolphin Owner'S Manual preview
Sun Dolphin
Brand: KL Outdoor Pages: 8
Friday Harbor FH202 Quick Manual preview
FH202
Brand: Friday Harbor Pages: 8
komodo KDKX1INFKYA User Manual preview
KDKX1INFKYA
Brand: komodo Pages: 12
SKEETA FOILING CRAFT Nikki 5.5 Rigging Manual preview
Nikki 5.5
Brand: SKEETA FOILING CRAFT Pages: 32
SKEETA FOILING CRAFT NIKKI Rigging Manual preview
NIKKI
Brand: SKEETA FOILING CRAFT Pages: 32
Hunter H356 Owner'S Manual preview
H356
Brand: Hunter Pages: 145
TAKACAT T240L Owner'S Manual preview
T240L
Brand: TAKACAT Pages: 4
San Juan Yachting Mariah Owners’ Notes preview
Mariah
Brand: San Juan Yachting Pages: 35
Zodiac MEDLINE 9 Manual preview
MEDLINE 9
Brand: Zodiac Pages: 65
Old Town Canoe Co. 01.1315.2380 Owner'S Manual preview
01.1315.2380
Brand: Old Town Canoe Co. Pages: 24
Walker Bay Generalion Owner'S Manual preview
Generalion
Brand: Walker Bay Pages: 26
West Marine Inflatable Boats Owner'S Manual preview
Inflatable Boats
Brand: West Marine Pages: 12
Oru Kayak BAY+ Assembly Manual preview
BAY+
Brand: Oru Kayak Pages: 20
Carolina Cat 23CC 2015 Owner'S Manual preview
23CC 2015
Brand: Carolina Cat Pages: 65
Sea Eagle Stealth Stalker 10 Basic Instructions preview
Stealth Stalker 10
Brand: Sea Eagle Pages: 2
Sportime 3662902 User Manual preview
3662902
Brand: Sportime Pages: 25
Silver Eagle BR Owner'S Manual preview
Eagle BR
Brand: Silver Pages: 215

Brands by name

Popular brands

Load more brands