Yamaha GP800R WaveRunner 2003 Service Manual Download Page 104

Page: 104 / 247

5-19

POWR

CYLINDER HEAD

SERVICE POINTS

Cylinder head inspection

1. Eliminate:

●

Carbon deposits
(with a rounded scraper

)

CAUTION:

Do not use a sharp instrument to avoid
damaging or scratching the cylinder head
or spark plug bore threads.

2. Inspect:

●

Cylinder head water jacket
Corrosion/mineral deposits

→

Clean

or replace.

3. Measure:

●

Cylinder head warpage
(with a straightedge and thickness
gauge)
Out of specification/score marks

→

Resurface.

NOTE:

Place a 400–600 grit wet sandpaper on a
surface plate and resurface the cylinder
head using a figure-eight sanding pattern.

Warpage limit:

0.1 mm (0.004 in)

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands

Yamaha GP800R WaveRunner 2003, Service Manual

Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands