Yamaha GP800R WaveRunner 2003 Service Manual Download Page 199

Page: 199 / 247

8-8

HULL

HOOD

HANDLEBAR

3. Install:

●

Throttle cable

NOTE:

Fit the seal into the glove in the bracket.

4. Install:

●

Band

NOTE:

After inserting the QSTS cables into the
grommet, tie the end of grommet with the
band.

5. Install:

●

Spiral tube

NOTE:

Be sure to install the spiral tube, containing
the throttle cable, choke cable and handle-
bar switch lead, at least 50 mm (1.97 in)

into the steering column.

6. Install:

●

Handlebar cover

NOTE:

When the handlebar cover is in contact with
the steering console cover, adjust the han-
dlebar mount angle so that the clearance

and

are equal.

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands

Yamaha GP800R WaveRunner 2003, Service Manual

Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands