Yamaha FZ6-NSV Owner'S Manual Download Page 68 | Manualshive

Page: 68 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-28

EAU34380

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the bolts on each side.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10660

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al-
cohol or thinner.

1. Bolt

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder
2. Headlight bulb

U1B322E0.book Page 28 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
66
67
68
69
70
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

Fastrax 50144-00

Brand: Dowco Pages: 3

Brand: X-lite Pages: 84

Brand: Regal Raptor Pages: 48

Brand: CRATONI Pages: 61

Brand: Honda Pages: 137

Brand: KTM Power Parts Pages: 12

Brand: rizoma Pages: 16

Brand: Kabuto Pages: 6

KODIAK YFM70KDXM

Brand: Yamaha Pages: 180

Brand: Yamaha Pages: 156

RAPTOR 700R 2022

Brand: Yamaha Pages: 160

Brand: Pacific Helmets Pages: 40

Brand: Yamaha Pages: 110

Brand: DYNATEK Pages: 6

Brand: DYNATEK Pages: 12

Brand: BMW Pages: 205

Brand: hepco & becker Pages: 2

Brand: Rally-Raid Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands