Yamaha FZ6-NSV Owner'S Manual Download Page 73

Page: 73 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

7. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU34411

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.
2. Lift the rear wheel off the ground

according to the procedure on
page 6-31.

3. Remove the axle nut.
4. Loosen the locknut and drive chain

adjusting nut on each side of the
swingarm.

5. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

1. Axle nut
2. Drive chain slack adjusting nut

3. Locknut

U1B322E0.book Page 33 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

Summary of Contents for FZ6-NSV



























































































Search results

Summary of Contents for FZ6-NSV

Reviews:

Related manuals for FZ6-NSV

Brands by name

Popular brands

Yamaha FZ6-NSV, Owner'S Manual

Search results

Summary of Contents for FZ6-NSV

Reviews:

Related manuals for FZ6-NSV

Brands by name

Popular brands