Yamaha FZ6-NSV Owner'S Manual Download Page 63

Page: 63 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

EAU23200

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10730

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

EAUM1650

Lubricating the swingarm
pivots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease

U1B322E0.book Page 23 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

Summary of Contents for FZ6-NSV



























































































Search results

Summary of Contents for FZ6-NSV

Reviews:

Related manuals for FZ6-NSV

Brands by name

Popular brands

Yamaha FZ6-NSV, Owner'S Manual

Search results

Summary of Contents for FZ6-NSV

Reviews:

Related manuals for FZ6-NSV

Brands by name

Popular brands