Yamaha FZ6-NSV Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 90

background image

OPERATION AND IMPORTANT RIDING POINTS

5-2

CAUTION:

ECA11130

For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

NOTE:

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

CAUTION:

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

1. Shift pedal

2. Neutral position

U1B322E0.book Page 2 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
36
37
38
39
40
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: hepco & becker Pages: 5

Brand: Braaap Pages: 40

Brand: Cake Pages: 12

Brand: GAS GAS Pages: 107

Battery Relocation Kit

Brand: BoxerCafe Pages: 7

Brand: BMW Pages: 139

Brand: Honda Pages: 93

Brand: Dynajet Pages: 20

Brand: VESPA Pages: 82

Brand: Dynafit Pages: 52

Brand: JAWA Pages: 22

SPYDER F3TM 2016

Brand: Can-Am Pages: 171

Brand: BMS Pages: 11

Brand: O'Neal Pages: 12

Brand: APRILIA Pages: 80

Brand: hepco & becker Pages: 2

Brand: KTM Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands