Yamaha FZ6-NSV Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 90

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-3

3

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

WARNING

EWA10060

Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped be-
fore turning the key to “OFF” or
“LOCK”.

EAU34341

(Parking)

The steering is locked, and the taillight,
license plate light and auxiliary light are
on. The hazard lights and turn signal
lights can be turned on, but all other
electrical systems are off. The key can
be removed.
The steering must be locked before the
key can be turned to “

”.

CAUTION:

ECA11020

Do not use the parking position for
an extended length of time, other-
wise the battery may discharge.

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “

” and

“

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

1. Push.
2. Turn.

1. Oil level warning light “

”

2. Engine trouble warning light “

”

3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Immobilizer system indicator light “

”

6. Turn signal indicator lights “

” and “

”

U1B322E0.book Page 3 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
17
18
19
20
21
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

Brand: B-PWR Pages: 12

Brand: GAS GAS Pages: 56

Brand: Sicor Pages: 2

6513515 00 22-00-40

Brand: hepco & becker Pages: 7

Brand: Husqvarna Pages: 7

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 58

Brand: Yamaha Pages: 42

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 77

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 112

Star Venture 2018

Brand: Yamaha Pages: 116

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands