Yamaha FZ6-NSV Owner'S Manual Download Page 55 | Manualshive

Page: 55 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-15

6

NOTE:

The tire tread depth limits may differ
from country to country. Always comply
with the local regulations.

Tire information

This motorcycle is equipped with cast
wheels and tubeless tires with valves.

WARNING

EWA10480

●

The front and rear tires should
be of the same make and de-
sign, otherwise the handling
characteristics of the motor-
cycle cannot be guaranteed.

●

After extensive tests, only the
tires listed below have been ap-
proved for this model by
Yamaha Motor Co., Ltd.

●

Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.

●

Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

1. Tire air valve

2. Tire air valve core
3. Tire air valve cap with seal

Front tire:

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

BRIDGESTONE/BT020F GG
DUNLOP/D252F

Rear tire:

Size:

180/55 ZR17M/C (73W)

Manufacturer/model:

BRIDGESTONE/BT020R GG
DUNLOP/D252

FRONT and REAR:

Tire air valve:

TR412

Valve core:

#9100 (original)

U1B322E0.book Page 15 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
53
54
55
56
57
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

Brand: GAS GAS Pages: 70

Brand: Yamaha Pages: 88

Brand: Thunderbike Pages: 11

Monarch Pass M321

Brand: Wolfman Pages: 5

Brand: Crivit Pages: 70

COMFORT 10130810

Brand: Contracor Pages: 36

Brand: R&G Pages: 12

Brand: BMW Pages: 139

Brand: hepco & becker Pages: 4

Brand: PMI Pages: 2

Brand: Arai Pages: 2

Brand: Yamaha Pages: 93

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 74

Brand: Yamaha Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands