Yamaha FZ6-NSV Owner'S Manual Download Page 51 | Manualshive

Page: 51 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-11

6

EAU34423

Replacing the air filter element

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the seat. (See page

2. Remove the fuel tank bolts, and

then lift the fuel tank away from the
air filter case.

3. Remove the air filter case cover by

removing the screws.

4. Pull the air filter element out.

5. Insert a new air filter element into

the air filter case.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

6. Install the air filter case cover by in-

stalling the screws.

7. Place the fuel tank in the original

position and install the bolts.

WARNING

EWA12462

●

Before placing the fuel tank in
the original position, make sure
that all hoses (i.e., fuel hose,
fuel tank breather hose, fuel
tank overflow hose) are not
damaged, that they are properly
connected and routed, and that
they are not pinched.

●

If any hose is damaged, have a
Yamaha dealer replace the hose
before starting the engine, oth-
erwise fuel may leak.

1. Bolt

1. Screw
2. Air filter case cover

1. Air filter element
2. Air filter case

U1B322E0.book Page 11 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
49
50
51
52
53
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

Brand: R&G Pages: 4

Brand: SCORPION Pages: 12

Brand: DMC Pages: 2

Brand: Honda Pages: 100

Brand: Dakota Digital Pages: 6

Brand: Ohlins Pages: 8

HUSABERG MX 2000

Brand: Ohlins Pages: 16

Brand: Lakeland Pages: 16

Brand: B&G electronics Pages: 5

Brand: Yamaha Pages: 390

Brand: Yamaha Pages: 468

Brand: Yamaha Pages: 364

HPS SafeGuard Series

Brand: Dräger Pages: 40

Brand: KTM Pages: 53

Brand: Royal Enfield Pages: 110

Brand: 3M Pages: 7

Brand: 3M Pages: 26

Brand: Qingqi Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands