5 - 16
ENG
CAMSHAFTS
4. Install:
• camshaft cap bolts
NOTE:
@
Tighten the camshaft cap bolts in stages and
in a crisscross pattern, working from the inner
caps out.
CAUTION:
@
• Lubricate the camshaft cap bolts with the
engine oil.
• The camshaft cap bolts must be tightened
evenly or damage to the cylinder head,
camshaft caps, and camshafts will result.
• Do not turn the crankshaft when installing
the camshaft to avoid damage or
improper valve timing.
T
R
.
.
10 Nm (1.0 m · kg, 7.2 ft · lb)
5. Install:
• timing chain tensioner
▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
a. While lightly pressing the timing chain ten-
sioner rod by hand, turn the tensioner rod
fully clockwise with a thin screwdriver
1
.
NOTE:
@
Make sure that the tensioner rod has been fully
set clockwise.
b. With the timing chain tensioner rod turned
all the way into the timing chain tensioner
housing (with the thin screwdriver still
installed), install the gasket and the timing
chain tensioner
2
onto the cylinder block.
WARNING
@
Always use a new gasket.
c. Tighten the timing chain tensioner bolts
3
to the specified torque.
T
R
.
.
Timing chain tensioner bolt
10 Nm (1.0 m · kg, 7.2 ft · lb)
Summary of Contents for FJR1300R
