Yamaha F9.9 Owner'S Manual Download | Manualshive

Page: 87 / 112

background image

Maintenance

81

EMU28992

Checking fuel filter

Check the fuel filter periodically. The fuel filter
is a one piece, disposable type. If foreign
matter is found in the filter, replace it. For re-
placement of the fuel filter, consult your
Yamaha dealer.

EMU29045

Inspecting idle speed

WARNING

EWM00452



Do not touch or remove electrical parts
when starting or during operation.



Keep hands, hair, and clothes away
from the flywheel and other rotating
parts while the engine is running.

NOTICE

ECM00491

This procedure must be performed while
the outboard motor is in the water. A flush-
ing attachment or test tank can be used.

If the boat is not equipped with a tachometer
for the outboard motor, use a diagnostic ta-
chometer for this procedure. Results may
vary depending on whether testing is con-
ducted with the flushing attachment, in a test
tank, or with the outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smoothly.

2.

Once the engine has warmed up, verify
whether the idle speed is set to specifi-
cation. For idle speed specifications, see
page 15. If you have difficulty verifying
the idle speed, or the idle speed requires
adjustment, consult a Yamaha dealer or
other qualified mechanic.

EMU38808

Changing engine oil

WARNING

EWM00761



Avoid draining the engine oil immediate-
ly after stopping the engine. The oil is
hot and should be handled with care to
avoid burns.



Be sure the outboard motor is securely
fastened to the transom or a stable
stand.

NOTICE

ECM01711

Change the engine oil after the first 20
hours of operation or 3 months, and every
100 hours or at 1-year intervals thereafter.
Otherwise the engine will wear quickly.

To prevent spilling oil where it could cause
damage to nature, it is strongly recommend-
ed that you use an oil changer to change the
engine oil. If an oil changer is not available,
drain the engine oil by removing the drain
screw. If you are not familiar with the proce-
dure for changing the engine oil, consult your
Yamaha dealer.
1.

Put the outboard motor in an upright po-
sition (not tilted).

NOTICE:

If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

1. Fuel filter

1

ZMU07836

U6DR38E0.book Page 81 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
85
86
87
88
89
...
»

Summary of Contents for F9.9

















































































































Reviews:

No comments

Related manuals for F9.9

Brand: SOLTEK Pages: 49

Brand: ASROCK Pages: 5

Brand: Atmel Pages: 23

Brand: BESTEK Pages: 47

Brand: BCM Pages: 5

Brand: Texas Instruments Pages: 19

Brand: ITOX Pages: 114

Brand: Texas Instruments Pages: 15

Brand: Caji Pages: 19

Brand: ASROCK Pages: 20

Brand: Gigabyte Pages: 88

Brand: ECS Pages: 87

Development Board Type A

Brand: RoboMaster Pages: 21

Desktop Board D850EMD2

Brand: Intel Pages: 24

Brand: AOpen Pages: 8

Brand: JETWAY Pages: 48

Brand: Asus Pages: 64

Brand: Asus Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands