Yamaha F9.9 Page 4 Owner'S Manual Download

Page: 4 / 112

Table of contents

Safety information............................. 1

Outboard motor safety.................... 1

Boating safety ................................. 2

Alcohol and drugs ..............................  2
Personal flotation devices (PFDs) ......  2
People in the water ............................  2
Passengers.........................................  2
Overloading ........................................  2
Avoid collisions ..................................  3
Collisions with floating or submerged

objects ............................................ 3

Weather ..............................................  3
Accident reporting..............................  4
Boat education and training ...............  4
Passenger training .............................  4
Boating safety publications................  4
Laws and regulations .........................  4

Boating organizations ..................... 5
Basic boating rules (Rules of the

road) ............................................. 5

Steering and sailing rules and sound

signals............................................. 5

Rules when encountering vessels...... 6
Other special situations...................... 7

General information .......................... 9

Identification numbers record ......... 9

Outboard motor serial number........... 9
Key number ........................................ 9

Compliance mark label ................... 9
Read manuals and labels.............. 11

Warning labels ................................. 11

Specifications and
requirements ................................... 15

Specifications ............................... 15
Installation requirements .............. 16

Boat horsepower rating.................... 16
Mounting outboard motor ................ 17

Remote control requirements ....... 17
Battery requirements .................... 17

Specifications of Battery .................. 17
To install the battery......................... 17

Propeller selection ........................  18
Start-in-gear protection ................  18
Engine oil requirements ................  19
Fuel requirements .........................  19

Gasoline ........................................... 19
Gasoline Additives............................ 20

Muddy or acidic water .................. 21
Anti-fouling paint .......................... 21
Outboard motor disposal

requirements.............................. 22

Emergency equipment.................. 22
Emission control information ....... 22

Star labels ........................................ 22

Components .................................... 24

Components diagram ................... 24

clip ................................................ 30

U6DR38E0.book Page 1 Tuesday, November 27, 2018 2:08 PM

Summary of Contents for F9.9

















































































































Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands

Yamaha F9.9, Owner'S Manual

Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands