Yamaha F9.9 Page 25 Owner'S Manual Download | Manualshive

Page: 25 / 112

background image

Specifications and requirements

19

EMU39693

Engine oil requirements

Select an oil grade according to the average
temperatures in the area where the outboard
motor will be used.

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an al-
ternative oil grade listed under
Recommended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36361

Fuel requirements

EMU41333

Gasoline

Use a good quality gasoline that meets the
minimum octane requirement. If knocking or
pinging occurs, use a different brand of gas-
oline or premium unleaded fuel. Yamaha rec-
ommends that you use alcohol-free gasoline
(see Gasoline with Ethanol) whenever possi-
ble.
The use of a poor quality gasoline may result
in starting and running problems. If you en-
counter drivability problems, which you sus-
pect could be related to the fuel you are
using, Yamaha recommends that you switch
to a recognized high quality brand of gaso-
line, such as a gasoline that is advertised as
Top Tier Detergent Gasoline.

NOTICE:

Fail-

ure to comply with these recommenda-
tions may also result in unscheduled
maintenance, fuel system damage, and in-
ternal engine damage.

[ECM04480]

NOTICE

ECM01982



Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.



Avoid getting water and contaminants in
the fuel tank. Contaminated fuel can
cause poor performance or engine dam-
age. Use only fresh gasoline that has
been stored in clean containers.

Gasoline with Ethanol

Two types of gasoline are commonly avail-
able in the U.S.A. and Canada for use in au-
tomobiles and boats: conventional gasoline

Recommended engine oil:

YAMALUBE 4M FC-W or 4-stroke
outboard motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL

Engine oil quantity:

0.8 L (0.85 US qt, 0.70 Imp.qt)

ZMU06

8

54

122˚F

50˚C

104

40

8

6

30

6

8

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06

8

55

122˚F

50˚C

104

40

8

6

30

6

8

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

Recommended fuel:

Regular unleaded gasoline

Min. pump octane number (PON):

86

U6DR38E0.book Page 19 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
23
24
25
26
27
...
»

Summary of Contents for F9.9

















































































































Reviews:

No comments

Related manuals for F9.9

Brand: IEI Technology Pages: 8

Brand: Linear Technology Pages: 10

Brand: Freetech Pages: 79

Brand: Linear Technology Pages: 7

Brand: Tadao Pages: 3

Brand: ECS Pages: 66

Brand: Gigabyte Pages: 44

Brand: Supermicro Pages: 229

Brand: OLIMEX Pages: 14

Brand: Watersnake Pages: 20

Brand: Infineon Pages: 14

Brand: Taiwan Commate Computer Inc. Pages: 31

Brand: GigaDevice Semiconductor Pages: 16

Brand: TYAN Pages: 81

Brand: IMS Pages: 14

Brand: DFI Pages: 105

Brand: ASROCK Pages: 107

Brand: ASROCK Pages: 145

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands