Yamaha F9.9 Page 91 Owner'S Manual Download

Page: 91 / 112

Maintenance

Remove the propeller, washer (if
equipped), and thrust washer.

EMU46500

Dual thrust models

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer.

WARNING! Do not use your

hand to hold the propeller when loos-
ening the propeller nut.

[EWM01891]

Remove the propeller, washer, and
thrust washer.

EMU30673

Installing propeller

EMU29237

Spline models

NOTICE

ECM00502

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

Apply Yamaha marine grease or a corro-
sion resistant grease to the propeller
shaft.

Install the spacer (if equipped), thrust
washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01882]

Install the spacer (if equipped) and the
washer. Tighten the propeller nut to the
specified torque.

1. Cotter pin
2. Propeller nut
3. Washer
4. Propeller
5. Thrust washer

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

ZMU08166

ZMU08167

1. Cotter pin
2. Propeller nut
3. Washer
4. Propeller
5. Thrust washer

Propeller nut tightening torque:

17 N·m (1.7 kgf·m, 13 lb·ft)

ZMU08169

U6DR38E0.book Page 85 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Summary of Contents for F9.9

















































































































Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands

Yamaha F9.9, Owner'S Manual

Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands