manualshive.com logo in svg

Yamaha F9.9, Owner'S Manual, Page: 39 / 112

Share
Download
Yamaha F9.9 Owner'S Manual Download Page 39

Components

33

If the resistance does not increase even when
the lever is turned to the port side “A”, make
sure that the nut is tightened to the specified
torque.

TIP:

Steering movement is blocked when the
adjuster lever is set to the “A” position.

Check the tiller handle for smooth move-
ment when the lever is turned to the star-
board side “B”.

Do not apply lubricants such as grease to
the friction areas of the steering friction ad-
juster.

EMU26263

Trim rod (tilt pin)

The position of the trim rod determines the
minimum trim angle of the outboard motor in
relation to the transom.

EMU30531

Tilt lock mechanism

The tilt lock mechanism is used to prevent the
outboard motor from lifting out of the water
when in reverse gear.

To lock it, set the tilt lock lever in the lock po-
sition. To release, push the tilt lock lever in the
release position.

EMU26323

Tilt support knob

To keep the outboard motor in the tilted up
position, push the tilt support knob under the
swivel bracket.

1. Nut

Nut tightening torque:

8 N·m (0.8 kgf·m, 5.9 lb·ft)

1. Trim rod

1. Tilt lock lever

1

ZMU07813

1

ZMU07814

U6DR38E0.book  Page 33  Tuesday, November 27, 2018  2:08 PM

©2020 

Yamaha 

Motor 

Corporation

Summary of Contents for F9.9

















































































































Reviews:

No comments