Yamaha F9.9 Page 33 Owner'S Manual Download | Manualshive

Page: 33 / 112

background image

Components

27

EMU25831

Fuel joint

This joint is used to connect the fuel line.

EMU43151

Pressure relief tab

This is attached to the filler hole of the fuel
tank.

EMU43131

Fuel tank cap

This cap seals the fuel tank. To loosen the
cap, press and hold the pressure relief tab
and turn the cap counterclockwise.

EMU43142

Air vent screw

This screw is on the fuel tank cap. When turn-
ing the air vent screw counterclockwise, it is
loosened and the pressure in the fuel tank is
released to a certain pressure. Air is allowed
to enter the fuel tank while operating the en-
gine.

EMU26182

Remote control box

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

EMU26191

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

1. Fuel joint
2. Pressure relief tab
3. Fuel tank cap
4. Air vent screw

3

4

1

2

1. Power tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine shut-off switch
7. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”
4. Shift
5. Fully closed
6. Throttle
7. Fully open

1
2

3

5

4

6

7

ZMU01723

1

2

3

4

4

5

5

6

6

7

7

F

N

R

ZMU01725

U6DR38E0.book Page 27 Tuesday, November 27, 2018 2:08 PM

©2020

Yamaha

Motor

Corporation

«
...
31
32
33
34
35
...
»

Summary of Contents for F9.9

















































































































Reviews:

No comments

Related manuals for F9.9

Brand: IBM Pages: 357

Brand: NXP Semiconductors Pages: 14

AP0100CSSL00SPGAH-GEVB

Brand: ON Semiconductor Pages: 6

Nucleo STM32F302R8

Brand: ST Pages: 18

Brand: ASROCK Pages: 198

Brand: Gigabyte Pages: 100

Brand: Arbor Technology Pages: 86

SERVER SYSTEM SR2500AL

Brand: Intel Pages: 210

Brand: ASROCK Pages: 200

Brand: Aaeon Pages: 113

TPS5420EVM-175 SWIFT

Brand: Texas Instruments Pages: 16

Brand: Ublox Pages: 22

Brand: MSI Pages: 115

Brand: NavSpark Pages: 18

FM2A75M-DGS R2.0

Brand: ASROCK Pages: 59

Brand: Asus Pages: 58

Brand: Asus Pages: 74

Brand: Asus Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands