Yamaha F75D Page 6 Ower'S Manual Download | Manualshive

Page: 6 / 75

background image

General information

1

EMU25170

Identification numbers record

EMU25182

Outboard motor serial number

The outboard motor serial number is stamped
on the label attached to the port side of the
clamp bracket or the upper part of the swivel
bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is sto-
len.

EMU25190

Key number

If a main key switch is equipped with the mo-
tor, the key identification number is stamped
on your key as shown in the illustration.
Record this number in the space provided for
reference in case you need a new key.

EMU25220

Emission control information

EMU25230

North American models

This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.

EMU25242

Approval label of emission control certifi-
cate

This label is attached to the bottom cowling.
New Technology; (4-stroke/HPDI) EM

1. Outboard motor serial number location

1

ZMU04214

1. Key number

1. Approval label location

1

ZMU04217

U6D610E0.book Page 1 Tuesday, April 20, 2004 1:52 PM

«
...
4
5
6
7
8
...
»

Summary of Contents for F75D












































































Reviews:

No comments

Related manuals for F75D

Brand: Ublox Pages: 2

Brand: u-blox Pages: 24

Brand: Biostar Pages: 53

Brand: Safran Pages: 26

Brand: OLIMEX Pages: 17

Brand: ASROCK Pages: 145

Brand: JETWAY Pages: 49

Brand: Xilinx Pages: 56

tps61040EVM-002

Brand: Texas Instruments Pages: 31

4CORE1600-GLAN/M

Brand: ASROCK Pages: 102

Brand: Gigabyte Pages: 98

Brand: Texas Instruments Pages: 27

Brand: Gigabyte Pages: 96

Brand: Texas Instruments Pages: 21

Brand: Texas Instruments Pages: 13

Brand: Texas Instruments Pages: 15

Brand: TYAN Pages: 67

Brand: TYAN Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands