Yamaha F75D Page 18 Ower'S Manual Download | Manualshive

Page: 18 / 75

background image

Basic components

13

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into either
forward or reverse, put the remote control le-
ver in the neutral position and lift the neutral
throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed
position.

EMU25970

Throttle friction adjuster

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.

2. Remote control lever
3. Neutral interlock trigger

4. Neutral throttle lever

5. Main switch / choke switch
6. Engine stop lanyard switch

7. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”

3. Reverse “ ”

4. Shift
5. Fully closed

6. Throttle

7. Fully open

1. Neutral interlock trigger

1. Fully open

2. Fully closed

U6D610E0.book Page 13 Tuesday, April 20, 2004 1:52 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for F75D












































































Reviews:

No comments

Related manuals for F75D

Brand: Zapi Pages: 50

RouterBOARD 411

Brand: 4gon Pages: 2

Brand: Gigabyte Pages: 8

Analog Devices DC2605A

Brand: Linear Pages: 16

Brand: Texas Instruments Pages: 16

MITX-DNV0 Series

Brand: Quanmax Pages: 84

Brand: National Semiconductor Pages: 22

Brand: MSI Pages: 91

Brand: TransCore Pages: 40

Brand: DG Pages: 18

Brand: EVGA Pages: 40

Brand: Microchip Technology Pages: 54

Brand: Gigabyte Pages: 88

Brand: DFI Pages: 99

Brand: morse Pages: 70

Brand: JETWAY Pages: 42

Brand: Terra Pages: 6

Brand: FuzzDog Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands