Yamaha F75D Page 22 Ower'S Manual Download | Manualshive

Page: 22 / 75

background image

Basic components

17

EMU26460

Flushing device

This device is used to clean the cooling water
passages of the motor using a garden hose
and tap water.

NOTE:

For details on usage, see page 40.

EMU26491

Digital tachometer

The tachometer shows the engine speed and
has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

NOTE:

The water separator and engine trouble warn-
ing indicators only operate when the engine is
equipped with the appropriate functions.

EMU26521

Low oil pressure warning indicator

If oil pressure drops too low, the warning indi-
cator will start to blink. For further information,
see page 21.

CAUTION:

ECM00020

●

Do not continue to run the engine if the
low oil pressure warning indicator is on
and the engine oil level is lower. Serious
engine damage will occur.

●

The low oil pressure warning indicator
does not indicate the engine oil level.
Use the oil dipstick to check the remain-
ing oil quantity. For further information,
see page 25.

1. Top cowling lock lever(s)

1. Flushing device

ZMU04226

1

1. Tachometer

2. Trim meter

3. Hour meter

4. Low oil pressure warning indicator
5. Overheat warning indicator

6. Set button

7. Mode button

ZMU01840

1

5

2

4

3

6

7

U6D610E0.book Page 17 Tuesday, April 20, 2004 1:52 PM

«
...
20
21
22
23
24
...
»

Summary of Contents for F75D












































































Reviews:

No comments

Related manuals for F75D

Brand: P&E Microcomputer Systems Pages: 59

Brand: Danbit Pages: 70

Brand: JETWAY Pages: 46

Brand: Intel Pages: 110

Brand: Aaeon Pages: 50

Brand: AOpen Pages: 8

Brand: Gigabyte Pages: 92

Brand: DFI Pages: 46

Brand: Seanix Pages: 49

Brand: Advantech Pages: 104

Brand: Intel Pages: 73

Brand: Renesas Pages: 6

NF4 SLI INFINITY

Brand: DFI Pages: 127

Brand: OCR Pages: 20

K7VM400M Pro Series

Brand: QDI Pages: 62

Brand: Biostar Pages: 47

Brand: NavSpark Pages: 17

Brand: Foxconn Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands