Yamaha F75D Page 38 Ower'S Manual Download | Manualshive

Page: 38 / 75

background image

Operation

33

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever toward
you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure to
support it with the tilt support knob or tilt
support lever. Otherwise the outboard mo-
tor could fall back down suddenly if oil in
the power trim and tilt unit loses pressure.

5.

Models equipped with trim rods: Once the
outboard motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

CAUTION:

ECM00250

Be sure to retract the trim rods completely
during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt
mechanism.

EMU28053

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt sup-
port lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

3.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

UP

ZMU04232

DN

ZMU01936

UP

DN

U6D610E0.book Page 33 Tuesday, April 20, 2004 1:52 PM

«
...
36
37
38
39
40
...
»

Summary of Contents for F75D












































































Reviews:

No comments

Related manuals for F75D

Brand: Qorvo Pages: 8

Brand: Gigabyte Pages: 93

Brand: Gigabyte Pages: 100

Brand: Intel Pages: 97

Brand: DIEBOLD NIXDORF Pages: 96

790XT-G35 series

Brand: MSI Pages: 103

Brand: Texas Instruments Pages: 35

Brand: ITX SECURITY Pages: 18

Supero C9X299-PG300F

Brand: Supermicro Pages: 28

Brand: Supermicro Pages: 121

Development Board Type A

Brand: RoboMaster Pages: 21

Brand: PC Chips Pages: 49

X58A-GD65 series

Brand: MSI Pages: 100

Brand: ASROCK Pages: 25

Brand: MotorGuide Pages: 31

Brand: u-blox Pages: 33

Brand: Shift838 Pages: 9

Brand: ASROCK Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands