Yamaha F75D Page 55 Ower'S Manual Download | Manualshive

Page: 55 / 75

background image

Maintenance

50

NOTE:

Consult your Yamaha dealer if any operation
is abnormal.

EMU29171

Checking propeller

WARNING

EWM00321

You could be seriously injured if the en-
gine accidentally starts when you are near
the propeller.

●

Before inspecting, removing, or install-
ing the propeller, remove the spark plug
caps from the spark plugs. Also, place
the shift control in neutral, turn the main
switch to “

” (off) and remove the key,

and remove the lanyard from the engine
stop switch. Turn off the battery cut-off
switch if your boat has one.

●

Do not use your hand to hold the propel-
ler when loosening or tightening the
propeller nut. Put a wood block between
the anti-cavitation plate and the propel-
ler to prevent the propeller from turning.

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventilation,
or other damage.

●

Check the propeller shaft for damage.

●

Check the splines / shear pin for wear or
damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-
age.

NOTE:

If the shear pin equipped: it is designed to
break if the propeller hits a hard underwater
obstacle to help protect the propeller and
drive mechanism. The propeller will then spin
freely on the shaft. If this happens, the shear
pin must be replaced.

ZMU04262

ZMU01897

U6D610E0.book Page 50 Tuesday, April 20, 2004 1:52 PM

«
...
53
54
55
56
57
...
»

Summary of Contents for F75D












































































Reviews:

No comments

Related manuals for F75D

Brand: Yamaha Pages: 497

Brand: IBASE Technology Pages: 33

Brand: Gigabyte Pages: 8

Brand: AOpen Pages: 8

Brand: Gan Systems Pages: 28

Brand: Sail Pages: 18

Brand: Gigabyte Pages: 36

Brand: AKM Pages: 30

Brand: RAK Pages: 17

EmbCore ROM-7421

Brand: Advantech Pages: 25

Brand: NXP Semiconductors Pages: 14

Brand: Texas Instruments Pages: 18

NuMicro NuTiny-SDK-NANO100

Brand: Nuvoton Pages: 18

Brand: JETWAY Pages: 48

JW-A880GMT-EXTREME

Brand: J&W Pages: 39

Brand: ASROCK Pages: 244

Brand: IDT Pages: 18

MBD-X11SDV-4C-TP8F-B

Brand: Supermicro Pages: 123

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands