Yamaha 2008 XVS11AWX Owner'S Manual Download Page 92

Page: 92 / 96

INDEX

Air filter element, cleaning..................... 6-11
Auxiliary light bulb, replacing

(XVS11AWX)...................................... 6-31

Battery................................................... 6-27
Brake and clutch levers, checking and

lubricating ........................................... 6-24

Brake and shift pedals, checking and

lubricating ........................................... 6-23

Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-21
Brake lever.............................................. 3-9
Brake lever free play, adjusting............. 6-19
Brake pedal............................................. 3-9

Cables, checking and lubricating .......... 6-22
Carburetors, adjusting........................... 6-12
Care ........................................................ 7-1
Clutch lever ............................................. 3-8
Clutch lever free play, adjusting............ 6-18

Dimmer switch ........................................ 3-7

Engine break-in....................................... 5-5
Engine idling speed............................... 6-12
Engine oil ................................................ 6-8
Engine, starting a warm .......................... 5-4
Engine stop switch .................................. 3-7
Engine trouble warning light.................... 3-5

Final gear oil ........................................... 6-9
Front and rear brake pads, checking .... 6-20
Front fork, checking .............................. 6-25

Fuel....................................................... 3-10
Fuel cock .............................................. 3-11
Fuel consumption, tips for reducing........ 5-5
Fuel tank cap .......................................... 3-9
Fuses, replacing ................................... 6-28

Handlebar switches ................................ 3-6
Hazard switch (XVS11AWX) .................. 3-7
Headlight bulb, replacing ...................... 6-30
Helmet holder ....................................... 3-15
High beam indicator light ........................ 3-4
Horn switch............................................. 3-7

Identification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-20
Immobilizer system indicator

light (XVS11AWX)................................ 3-5

Immobilizer system (XVS11AWX) .......... 3-1
Indicator and warning lights.................... 3-4

Key identification number ....................... 9-1

Labels, location of................................... 1-5
Luggage strap holders.......................... 3-19

Main switch/steering lock

(XVS11AWX) ....................................... 3-2

Main switch/steering lock (XVS11X)....... 3-2
Matte color, caution ................................ 7-1
Model label ............................................. 9-2

Neutral indicator light.............................. 3-4
Noise regulation (for Australia) ............... 9-2

Oil level warning light .............................. 3-4

Panel, removing and installing ................6-6
Parking ....................................................5-6
Part locations .......................................... 2-1
Pass switch ............................................. 3-7
Periodic maintenance and lubrication

chart......................................................6-2

Pre-operation check list...........................4-2

Rear brake light switch, adjusting ......... 6-20
Rear suspension, lubricating................. 6-25

engine (XVS11AWX) ............................ 5-2

Starting and warming up a cold

engine (XVS11X) .................................. 5-1

Start switch..............................................3-7
Steering, checking.................................6-26
Storage....................................................7-3

U3B822E0.book Page 1 Tuesday, May 15, 2007 10:37 AM

Summary of Contents for 2008 XVS11AWX

































































































Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands

Yamaha 2008 XVS11AWX, Owner'S Manual

Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands