Yamaha 2008 XVS11AWX Owner'S Manual Download Page 54 | Manualshive

Page: 54 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-6

6

EAU18751

Removing and installing the
panel

The panel shown needs to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time the panel needs
to be removed and installed.

EAU19151

Panel A

To remove the panel
Remove the bolt, and then pull the pan-
el off as shown.

To install the panel
Place the panel in the original position,
and then install the bolt.

EAU19552

Checking the spark plugs

The spark plugs are important engine
components, which are easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plugs should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
the condition of the spark plugs can re-
veal the condition of the engine.

To remove a spark plug

1. Remove the appropriate spark

plug cover (rear right or front left)
by pulling it off as shown.

2. Remove the spark plug cap.

1. Panel A

1. Bolt

1. Spark plug cover

U3B822E0.book Page 6 Tuesday, May 15, 2007 10:37 AM

«
...
52
53
54
55
56
...
»

Summary of Contents for 2008 XVS11AWX

































































































Reviews:

No comments

Related manuals for 2008 XVS11AWX

Brand: Yamaha Pages: 662

Brand: GYS Pages: 36

DaVinci RSV4-APRC

Brand: STARLANE Pages: 2

Superbike 749R 2006

Brand: Ducati Pages: 608

Brand: DYNATEK Pages: 12

Brand: Yamaha Pages: 400

Brand: Ops-Core Pages: 20

ES350 BURROeSCOOTER

Brand: Burro Max Pages: 32

Brand: R&G Pages: 6

Brand: Shark Pages: 16

Brand: VOIGT MT Pages: 2

Brand: Voigt Pages: 2

Brand: Healtech Pages: 2

BRAKE LIGHT PRO

Brand: Healtech Pages: 2

Brand: Honda Pages: 293

Brand: hepco & becker Pages: 3

Brand: Honda Pages: 36

HIMALAYAN EURO IV 2017

Brand: Royal Enfield Pages: 294

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands