Yamaha 2008 XVS11AWX Owner'S Manual Download Page 77

Page: 77 / 96

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

3. Pull the ignitor unit panel outward

to the right.

4. Turn the key to “OFF” and turn off

the electrical circuit in question.

5. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

6. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

7. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

8. Place the ignitor unit panel in the

original position and install the
quick fasteners.

NOTE:

To install a quick fastener, push its pin
back so that it will protrude from the fas-
tener head, then insert the fastener and
push the protruding pin in until it is flush
with the fastener head.

9. Install the rider seat.

1. Quick fastener

1. Ignitor unit panel

2. Spare main fuse
3. Main fuse

Specified fuses:

Main fuse:

30.0 A

Backup fuse:

XVS11AWX 10.0 A
XVS11X 5.0 A

Ignition fuse:

10.0 A

Headlight fuse:

15.0 A

Carburetor heater fuse:

15.0 A

Signaling system fuse:

10.0 A

Parking lighting fuse:

XVS11AWX 10.0 A

1. Quick fastener (after removal)

2. Quick fastener (before installation)

U3B822E0.book Page 29 Tuesday, May 15, 2007 10:37 AM

Summary of Contents for 2008 XVS11AWX

































































































Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands

Yamaha 2008 XVS11AWX, Owner'S Manual

Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands