Yamaha 2008 XVS11AWX Owner'S Manual Download Page 48

Page: 48 / 96

OPERATION AND IMPORTANT RIDING POINTS

5-6

CAUTION:

ECA10331

After 1000 km (600 mi) of operation,
the engine oil and final gear oil must
be changed, and the oil filter car-
tridge or element replaced.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

CAUTION:

ECA10270

If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.

EAU17170

Parking

When parking, stop the engine, remove
the key from the main switch, and then
turn the fuel cock lever to “OFF”.

WARNING

EWA10310

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.

U3B822E0.book Page 6 Tuesday, May 15, 2007 10:37 AM

Summary of Contents for 2008 XVS11AWX

































































































Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands

Yamaha 2008 XVS11AWX, Owner'S Manual

Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands