Yamaha 2008 XVS11AWX Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-11

6

EAU20670

Cleaning the air filter element

The air filter element should be cleaned
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart. Clean the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the air filter case cover by

removing the screws.

2. Pull the air filter element out.
3. Lightly tap the air filter element to

remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.

4. Insert the air filter element into the

air filter case as shown.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

5. Install the air filter case cover by in-

stalling the screws.

1. Air filter case cover

2. Screw

1. Air filter element
2. Projection

3. Slot

U3B822E0.book Page 11 Tuesday, May 15, 2007 10:37 AM

«
...
57
58
59
60
61
...
»

Summary of Contents for 2008 XVS11AWX

































































































Reviews:

No comments

Related manuals for 2008 XVS11AWX

B-TRK502-02-01-SL

Brand: SRC Pages: 4

Brand: Parweld Pages: 4

Brand: IRC Pages: 2

Brand: Kabuto Pages: 20

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Road Star XV17AWX

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 650

Brand: hepco & becker Pages: 2

GHJ 10,8+18V Unisex

Brand: Bosch Pages: 14

Brand: Bosch Pages: 28

Brand: Bosch Pages: 145

Brand: Shark Pages: 92

Brand: Kinroad Pages: 26

Brand: Brixton Pages: 49

Brand: Datatool Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands