Yamaha 2008 XVS11AWX Owner'S Manual Download Page 79

Page: 79 / 96

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

EAU24281

Replacing a turn signal light
bulb or the tail/brake light bulb

1. Remove the lens by removing the

screws.

XVS11X

XVS11AWX

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

CAUTION:

ECA10680

Do not overtighten the screws, oth-
erwise the lens may break.

EAU33411

Replacing the auxiliary light
bulb (XVS11AWX)

If the auxiliary light bulb burns out, re-
place it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Remove the socket (together with

the bulb) by pushing it in and turn-
ing it counterclockwise.

1. Screw

U3B822E0.book Page 31 Tuesday, May 15, 2007 10:37 AM

Summary of Contents for 2008 XVS11AWX

































































































Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands

Yamaha 2008 XVS11AWX, Owner'S Manual

Search results

Summary of Contents for 2008 XVS11AWX

Reviews:

Related manuals for 2008 XVS11AWX

Brands by name

Popular brands