Yamaha 2008 XVS11AWX Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 96

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-8

3

EAU12820

Clutch lever

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-20.)

EAU12870

Shift pedal (XVS11X)

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU12880

Shift pedal (XVS11AWX)

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

NOTE:

Use your toes or heel to shift up and
your toes to shift down.

1. Clutch lever

1. Shift pedal

1. Shift pedal

U3B822E0.book Page 8 Tuesday, May 15, 2007 10:37 AM

«
...
24
25
26
27
28
...
»

Summary of Contents for 2008 XVS11AWX

































































































Reviews:

No comments

Related manuals for 2008 XVS11AWX

Brand: GBRacing Pages: 2

Brand: yasuni Pages: 8

Brand: GAS GAS Pages: 32

Brand: Baja motorsports Pages: 20

Brand: Yoshimura Pages: 7

Brand: Honda Pages: 110

GT650SR - PARTS CATALOGUE

Brand: HYOSUNG Pages: 124

Brand: zeeltronic Pages: 10

Spyder RT Series

Brand: Can-Am Pages: 52

Rally Pack Value Series

Brand: Dowco Pages: 3

Brand: Toolland Pages: 25

H-AFT18-15-01-SL

Brand: SRC Pages: 3

Operation and Instruction Manua

Brand: Takegawa Pages: 9

Brand: MOTO GUZZI Pages: 134

Brand: Honda Pages: 123

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 8

Brand: DYNATEK Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands