Yamaha 2008 Raptor 250 Service Manual Download Page 244

Page: 244 / 311

CHAS

6-39

WARNING

• Use only the designated quality brake

fluid: other brake fluids may deteriorate
the rubber seals, causing leakage and
poor brake performance.

• Refill with the same type of brake fluid:

mixing brake fluids may result in a harm-
ful chemical reaction and lead to poor
brake performance.

• Be careful that water does not enter the

master cylinder when refilling. Water will
significantly lower the boiling point of the
brake fluid and may result in vapor lock.

3. Air bleed:

• brake system

Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” in chapter 3.

4. Check:

• brake fluid level

Brake fluid level is below the “LOWER” level
line

→

Add the recommended brake fluid to

the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” in chapter 3.

FRONT AND REAR BRAKES

Summary of Contents for 2008 Raptor 250
























































































































































































































































































































Search results

Summary of Contents for 2008 Raptor 250

Reviews:

Related manuals for 2008 Raptor 250

Brands by name

Popular brands

Yamaha 2008 Raptor 250, Service Manual

Search results

Summary of Contents for 2008 Raptor 250

Reviews:

Related manuals for 2008 Raptor 250

Brands by name

Popular brands