background image

 

17

7. Limited Warranty 

  If an abnormality occurs during normal operation in accordance with the operating instructions and other operating 

cautions within the warranty period (12 months after date of purchase) that can be attributed to a manufacturing 
defect, the defective parts of this product will be serviced or the product will be replaced free of charge. However, 
this warranty will not cover compensation for incidental damage or any malfunction listed below. 

 

1. Warranty period

 

This warranty will be valid for a period of 12 months after the date of purchase. 

 

2. Warranty

 

If, during the warranty period, any of the material of the genuine parts of this product or the workmanship of this 
product is found defective, and is so verified by our company, the servicing cost will be fully born by our company. 

 

3. Exclusion

 

Even during the warranty period, this warranty does not cover the following. 
1)  Malfunction arising from use of parts other than manufacturer-specified genuine parts 
2)  Malfunction arising from misuse or operating errors, or lack of storage or maintenance care 
3)  Malfunction arising from use with a fluid that may cause corrosion, inflation or dissolution of the component 

parts of the product 

4)  Irregularity arising from repair made by other than by our firm, our regional office, dealer or authorized service 

personnel 

5)  Malfunction arising from modification of the product by other than authorized service personnel 
6)  Wear and tear of parts that must be regularly replaced in the course of normal operation, such as packings, 

O-rings and hose. 

7)

  Malfunction and/or damage due to use with incorrect voltage.

 

8)  Malfunction and/or damage due to transportation, moving or drop page of the product after purchase 
9)  Malfunction and/or damage due to fire, earthquake, flood or other force majeure 
10)  Malfunction arising from use of compressed air that contains impurities or excessive moisture, or use of gases 

or fluids other than the specified compressed air 

11)  Malfunction arising from use of excessively abrasive material or of inadequate grease.  
Furthermore, this warranty does not cover the rubber parts, or other parts used in this product and its accessories, 
which are subject to wear in normal operation. 

hoses

    ・

packings 

  ・

cords

 

 

 

4. Parts

 

Parts for this product will be kept available for 5 years after discontinuation of production. Once 5 years have 
elapsed after close of production, availability of parts for this product cannot be guaranteed.

 

Summary of Contents for 140 Series

























Reviews: